How to Make a Lattice Pie Crust: Strip Width, Weaving and Baking

Cut a lattice pie crust into strips 3/4 to 1 inch wide, weave them over a cold filling and bake hot first. Weaving steps, sealing, chilling and fixes.

Top view of cherry pie slices with lattice crust on a white surface.
Photo: Mariam Shahbazi / Pexels

A lattice pie crust is made by cutting a rolled-out round of pie dough into strips about 3/4 to 1 inch (2 to 2.5 cm) wide, weaving them over the filling in an over-and-under pattern, and sealing the ends to the bottom crust. Most lattice-top fruit pies bake at 425°F (220°C) for about 20 minutes, then at 375°F (190°C) for another 30 to 45 minutes, until the crust is deep golden and the filling bubbles thickly through the gaps.

A lattice needs the same dough as a double-crust pie, so start with enough for a top and bottom. Keep the dough cold throughout, because warm strips stretch, tear and shrink.

What dough works best for a lattice top?

Any standard double-crust pie dough works, as long as it holds together when cut into strips. An all-butter dough gives the best flavor and browning, and a dough made partly with shortening is a little more forgiving to handle. If you are making your own, the steps in our guide to all-butter pie crust from scratch cover mixing and chilling.

  • Divide the dough into two discs, one slightly larger for the bottom crust.
  • Chill both for at least 1 hour, or up to 2 days, before rolling.
  • Roll the top disc into a rough rectangle or circle about 1/8 inch (3 mm) thick and at least 11 inches (28 cm) across for a 9-inch (23 cm) pie.

How wide should lattice strips be?

Strips 3/4 to 1 inch (2 to 2.5 cm) wide are the easiest to handle and give a classic look with clear gaps for steam. Narrow strips of about 1/2 inch (1.3 cm) look delicate but break more easily and need a firmer, colder dough. Wide strips of 1 1/2 inches (4 cm) or more make a bold, rustic top and leave less of the filling exposed.

Use a ruler and a pizza wheel, pastry wheel or sharp knife. A fluted pastry wheel gives a scalloped edge. For a 9-inch (23 cm) pie you need 8 to 12 strips, depending on width. Cut a couple of extra strips in case one tears.

After cutting, slide the sheet of strips onto a baking sheet and chill for 15 to 20 minutes. Firm strips lift cleanly and keep straight edges.

How do you weave a lattice?

The standard method weaves the strips directly on the filled pie. Fit the bottom crust into the plate, add the cooled filling, and then:

  1. Lay half of the strips across the pie in one direction, parallel and evenly spaced, with gaps about as wide as the strips.
  2. Fold back every other strip halfway, to the center of the pie.
  3. Lay one strip across the center at a right angle to the first set.
  4. Unfold the folded strips over the new crosswise strip.
  5. Now fold back the alternate strips, the ones that stayed flat, and lay the next crosswise strip beside the first.
  6. Repeat, alternating which strips you fold, until one half of the pie is covered. Turn the pie and finish the other half the same way.

If the filling is juicy or the kitchen is warm, weave the lattice on a sheet of parchment paper instead, chill it until firm, and slide it onto the pie in one piece. This keeps the strips from soaking up filling while you work.

Simpler options exist. A “lazy” lattice lays all the strips of one direction flat, then lays the second set on top without weaving. It looks almost the same once baked.

How do you seal and trim the edges?

Trim the strip ends so they hang about 1/2 inch (1.3 cm) past the rim of the pie plate. Fold the overhang of the bottom crust up over the strip ends and press to seal, then crimp with your fingers or a fork. A good seal keeps the strips from pulling back toward the center as the pie bakes, which is one of the causes covered in our article on why pie crust shrinks.

Chill the finished pie for 20 to 30 minutes before baking. This firms the butter so the lattice holds its shape and flakes in the oven.

What should you brush on a lattice crust?

An egg wash gives a shiny, deep brown lattice. Beat 1 egg with 1 tablespoon of water or milk and brush a thin layer over the strips and edge, keeping it off the filling. For a softer, less glossy look, brush with milk or cream. A sprinkle of coarse sugar adds crunch and sparkle.

How long do you bake a lattice-top pie?

Bake on the lower rack, on a rimmed baking sheet to catch drips. Start at 425°F (220°C) for about 20 minutes to set the crust, then lower to 375°F (190°C) and bake 30 to 45 minutes more for most fruit pies. The pie is done when the lattice is deep golden and the filling bubbles slowly and thickly in the center gaps, not only at the edges. Thin, fast bubbles mean the thickener has not fully cooked yet.

The rim browns faster than the lattice. Once it reaches the color you want, cover it with foil strips or a pie shield; our guide to keeping pie crust edges from burning explains when to put them on. If the whole top darkens too early, lay a loose sheet of foil over the pie.

Let fruit pies cool for at least 3 to 4 hours so the filling sets before slicing. Fruit pies can stay at room temperature for up to 2 days, then go in the refrigerator, in line with FoodSafety.gov storage guidance. Custard and cream pies always need refrigeration.

What are the common lattice mistakes?

  • Strips that tear or stretch: the dough is too warm. Chill the strips again for 10 minutes.
  • Strips that sink into the filling: the filling was hot or very wet. Cool the filling first and use enough thickener.
  • Pale, doughy undersides on the strips: the oven was not hot enough at the start, or the pie baked too high in the oven.
  • Uneven gaps: measure the spacing with a ruler as you lay the first set of strips.
  • A soggy bottom crust: bake on the lowest rack, ideally on a preheated baking sheet.

Quick answers

Which pies suit a lattice top?

Fruit pies such as cherry, blueberry, peach and apple suit a lattice best, because the gaps let steam escape and show off the filling. Custard pies like pumpkin are usually baked without a top crust.

Can I make a lattice ahead of time?

Yes. Weave the lattice on parchment, cover it and refrigerate it for up to a day, or freeze it flat. Slide it onto the filled pie while it is still cold.

Do I need to cut vents in a lattice pie?

No. The open spaces between the strips let steam out, so no extra vents are needed.

Can I use store-bought dough for a lattice?

Yes. Refrigerated rolled pie dough cuts into strips well. Keep it cold and handle it as little as possible.